Structural Engineering & Statics
where the load goes
Concept

Neutral axis — where it appears

The line across a bent section where the stress is zero, at the centroid only while the material is elastic and the bar is straight. It moves as soon as the material stops being linear or the section stops being homogeneous, which is why a cracked or a fully plastic section has to be found by equilibrium.

Named by 26 essays across 5 fields — each of them below, with the objects they name alongside it.

Every strip counts by the square of its distance. A rectangular section divided into equal strips, with each strip's contribution to the second moment of area drawn beside it. The strips are identical in size; only their distance from the neutral axis differs.

The material far from the middle does nearly all the work

A strip of steel contributes to bending stiffness in proportion to the square of its distance from the centre. Move the same steel outward and the section gets stiffer for nothing.

sections · Second moment Bending is a push and a pull. A section carrying a bending moment, with the stress at every height computed as the moment times the distance from the neutral axis divided by the second moment of area. It is compression above and tension below, and zero exactly at the neutral axis.

Bending is a pair of forces, pushing and pulling

A bending moment is not a mysterious twisting. It is a push near the top of a section and a pull near the bottom, separated by a lever arm — a couple, made out of stress.

sections · Bending stress Where plane sections stop staying plane. Strain across a cut face at four span-to-depth ratios, with the straight line the theory assumes drawn faintly behind. For a slender beam the two coincide; for a beam as deep as its span the real distribution is nothing like a straight line, and beam theory has no claim on it.

Plane sections stay plane, and what the assumption costs

Beam theory rests on one sentence about geometry. It is very nearly true for a slender member, wrong for a deep one, and everything in the subject that fails does so where it stops holding.

sections · Plane sections Shear stress across a section. The distribution of shear stress over an I-section, computed as VQ/It by accumulating the first moment of the area above every height. The peak is 0.41 against a mean of 0.19 — a ratio of 2.15 — and it falls at the neutral axis, where the bending stress is zero.

The shear nobody draws

A stack of loose planks slides at its ends when it is loaded. Glue them and the sliding stops — and whatever the glue is now carrying is a stress that no bending calculation contains.

sections · Shear flow The neutral axis is wherever the first moment vanishes. A 300 by 500 section with 1200 mm² of steel at a depth of 450, carrying 150 kNm after the tension side has cracked. The neutral axis is no longer at mid-depth: it has risen to 137.0 mm from the top, which is where the first moment of the compression zone plus the transformed steel vanishes. The compression is 18.0 N/mm² at the top fibre and the steel carries 309 N/mm²; the resulting couple is 371 kN on a lever arm of 404 mm, which multiplies back to the 150 kNm applied. The uncracked section would have had 3422×10⁶ mm⁴ against the cracked 1139×10⁶ — a loss of 67% of the stiffness.

When half the section has given up

Bending theory puts the neutral axis through the centroid. That is a consequence, not a rule — and when the tension side cracks, the same reasoning moves the axis somewhere else entirely.

sections · Bending stress Shear stress across a section. The distribution of shear stress over an I-section, computed as VQ/It by accumulating the first moment of the area above every height. The peak is 82.77 against a mean of 38.46 — a ratio of 2.15 — and it falls at the neutral axis, where the bending stress is zero. At the junction between flange and web the flow is 820.0 per unit length, so connectors of 20000 each have to be spaced no further apart than 24 — which is what turns two pieces into one section.

The section made of pieces

Two plates bolted together are twice as strong as one plate. Two plates made to act as one section are eight times as stiff. The difference is entirely in the joint, and the joint has a calculable spacing.

sections · Second moment What it costs to reach the plastic moment, for two shapes. Moment against curvature for two cross-sections of identical area (3000 mm²) and identical depth (200 mm), in mild steel, each divided by its own first-yield moment and its own first-yield curvature. The rectangle has a shape factor of 1.50 and reaches 98% of its plastic moment at 4.1 times the curvature at first yield; The I-section has a shape factor of 1.09 and reaches 98% of its plastic moment at 1.1 times the curvature at first yield. The dashed lines are the rigid-plastic moments, computed from the equal-area axis rather than read off the curves, and no curve reaches its own.

The section that yields from the outside in

A rectangle has half again as much moment in reserve past first yield as its elastic capacity suggests, and an I-section has a seventh. Read as a ranking that gets it backwards — the reserve is bought with curvature, and the rectangle pays four times as much of it.

materials · Moment-curvature Two ways to fail, and the curve between them. The exact plastic interaction between axial force and moment for two sections of identical area, both normalised by their own squash load and their own plastic moment. The rectangle stands 25.0% of its plastic moment outside the straight line at an axial ratio of 0.50; The I-section stands 6.0% of its plastic moment outside the straight line at an axial ratio of 0.12. Every section here is symmetric about its centroid, so the equal-area axis and the centroid coincide and it makes no difference which the moments are taken about. The straight line is the rule that says the two capacities share out in proportion, and everything between it and a curve is capacity that rule gives away.

Two ways to fail, and the curve between them

A column carrying both compression and bending has two capacities and a rule for sharing them out. The rule is a straight line, the truth is a curve, and for a rectangle the straight line gives away a quarter of the plastic moment at half the squash load.

materials · Interaction Loaded straight down, and moving sideways. An equal angle with a moment applied about the horizontal axis. Its principal axes lie at 45.0° to the drawn ones, so the neutral axis runs at -30.6° rather than horizontally, and the section moves 59% as far sideways as it moves down. The product of inertia that causes it is -1.066 × 10⁶ mm⁴, and it is zero for every section drawn in this field until now.

Loaded straight down, and it moves sideways

Every section drawn here so far had an axis of symmetry, and that symmetry has been doing silent work. Take it away and a vertical load produces a neutral axis that is not horizontal, a deflection that is not vertical, and on one ordinary section a sideways movement larger than the downward one.

sections · Principal axes Cut the throat, and the face carries a moment and a tension at once. A crane hook of trapezoid section, 50 to 120 mm radius and 40 to 15 mm wide, carrying 50 kN, drawn beside the section at the cut and the stress across it. The load hangs on a line through the centre of curvature, so cutting the throat and taking everything below the cut as the free body leaves a face carrying a direct tension of 50 kN and a moment of N·R = 3.985 kN·m about the section's own centroid, which sits a full R = 79.70 mm from the load line. The stress is a hyperbola, zero at r = 75.04 mm rather than at the centroid 4.65 mm outside it, reaching 248.7 N/mm² of tension at the inner fibre and 140.6 of compression at the outer. The straight-beam formula, drawn dashed, reports 161.7 N/mm² for the bending part against the true 222.8, and leaves the 26.0 N/mm² of direct tension out altogether — between them, 54% under the real peak, at the fibre where a hook actually breaks. This is why a hook is trapezoidal: both effects are worst inside, so the material goes there.

The bar that was bent before it was loaded

In a curved bar plane sections still stay plane, and the bending formula is wrong anyway. The fibres were different lengths before anything was applied, so an equal rotation of two plane faces produces unequal strain — the stress is a hyperbola, the neutral axis has moved inward, and a crane hook carries half as much again as My/I reports.

sections · Curved beam Two beams, or one beam four times as stiff. Two 200 × 150 planks spanning 4 m under 6 per millimetre. Loose, they have 112.5×10⁶ mm⁴ between them and deflect 16.2 mm, with the two faces at the interface sliding past one another. Bonded, the pair has 450.0×10⁶ — exactly 4 times as much, because doubling a depth cubes — and deflects 4.0 mm at half the extreme-fibre stress. Nothing was added but a restraint on slip. With connectors of stiffness 200 the same beam deflects 5.4 mm, which is 89% of the way from one bound to the other.

Two beams, or one beam four times as stiff

Stack two planks and they bend as two beams whose faces slide past one another. Bond the faces and the pair has one neutral axis, four times the second moment and half the stress. Nothing was added but a restraint on slip.

internal-forces · Composite action One point, every plane through it, one circle. A point carrying 140 N/mm² across one face, 0 across the other and 45 of shear. As the plane is turned, the pair (σ, τ) runs round a circle of radius 83.2 centred at 70.0 — and it goes round at twice the rate the plane does, which is the part always misremembered and the part that makes the picture work. The principal stresses are 153.2 and -13.2, on planes 16.4° from the face the 140 acts on; the largest shear on any plane is 83.2, exactly the radius, and it sits 45° from those — which is 90° round the circle. The von Mises stress that ranks this state against any other is 160.2.

The worst stress is not where the worst bending is

Every stress this collection has quoted is a stress on a particular plane, and neither the bending stress nor the shear stress is a property of the point. Turn the plane and both change; one pair of numbers does not, and on a short beam it peaks where neither of them does.

sections · Principal stress The same strain, two moduli, and a width multiplied to say so. A timber section with a steel plate in it, carrying 20.0 kNm. Plane sections stay plane, so the strain at a height is the same in both materials; Hooke's law then puts the stresses in the ratio of the moduli, which here is 19.09. Multiplying the stiffer material's WIDTH by that ratio gives a fictitious section of one material with the same neutral axis and the same forces — 595.2×10⁶ mm⁴ of it, against 351.0 for the same shape with the moduli ignored. The steel plate is 3.8% of the area and carries 43% of the moment, at 96 N/mm² against the timber's 5.0. The transform is not an approximation: it is compatibility and Hooke's law written down.

A section made of two materials, one of them pretended away

Multiplying a material's width by the ratio of the moduli produces a fictitious section of one material with the right neutral axis and the right forces. It is not a trick — it is compatibility and Hooke's law written down — and it says a stiff material takes what its modulus asks for.

sections · Transformed section A section modulus for each face, and only the smaller one is a strength. Four profiles of equal area with the second moment divided by BOTH distances to an extreme fibre rather than by the larger of them. A symmetric section has one section modulus and an asymmetric one has two, differing here by as much as 1.00 to one — so the same member has two bending strengths, and which of them applies is decided by the sign of the moment rather than by anything about the section. The bar is the smaller of the two, which is the one that governs when the moment can go either way.

Two strengths, depending which way up

A symmetric section has one section modulus. A tee has two, differing by a factor of three, so the same member has two bending strengths and which applies is decided by the sign of the moment. Turn it over and it is a different beam.

sections · Asymmetric section Between two beams and one, and much nearer one. How composite a beam is, against the one dimensionless group that decides it: αL, where α² = K·EI∞/(EA*·EI₀). At αL = 0 the layers slide freely and the beam is two beams; past about 20 the connection is stiff enough that the last per cent is unbuyable. The beam drawn sits at αL = 15.8 and is 96% composite, deflecting 36.7 mm against 33.9 for full interaction and 110 for none. The curve is steep where a real design sits, which is why halving the number of studs does not halve anything.

Half the studs, and most of the beam

Bonding two layers together quadruples the stiffness of the pair. A real connection is a row of studs that deform, so the layers slide a little and the beam sits between the two answers — but not halfway between, and the number that decides where is a single dimensionless group.

internal-forces · Partial interaction Two faces, a couple, and a core that does none of it. A sandwich section 61.4 mm deep: two 0.7 mm faces separated by 60 mm of core. The bending is carried as a couple between the faces — 41 N/mm² of tension in one and compression in the other, over a lever arm of 60.7 mm — and the core carries a shear stress of 0.047 N/mm² and nothing else. The parallel-axis term is 98.8% of the section's second moment; the faces' own bending about their own centroids is 0.004% of it, and the core's is 1.2%. Separated by nothing at all the same two faces would be 2.3e+4 times less stiff.

Two skins and the space between them

A sandwich panel is a section made of a material that carries the bending and a material that carries none of it. The parallel-axis term is not a correction here — it is 98.8 per cent of the second moment — and the shear deflection is not a correction either.

sections · Sandwich section The neutral axis obeys neither the load nor the moment. A 305 × 102 mm I-section carrying a moment 5° out of the plane of its web. The moment vector is the short arrow; the neutral axis is the long line, at 69.7° to the strong axis. They do not line up, and the reason is that the neutral axis follows the moment ratio scaled by the stiffness ratio: tan α = (M_z/M_y)(I_y/I_z), and I_y ÷ I_z is 30.8 here. So a 5° tilt of the load puts the neutral axis 70° over, the corner that ends up furthest from it carries 489 N/mm² against the 258 the straight-down case would give, and the section has lost 47 per cent of its capacity to a misalignment nobody would draw on a detail.

Two moments and a neutral axis that obeys neither

Tilt the load on a rolled beam by five degrees and the neutral axis swings by seventy. The section is doubly symmetric, its product of inertia is exactly zero, and none of that helps — because what decides the axis is the moment ratio multiplied by a stiffness ratio of thirty.

sections · Biaxial bending What is left after the first fibre yields, which is a property of shape. The shape factor — plastic modulus over elastic — for six sections, computed by finding each one's equal-area axis and summing ±f_y over it. The numbers contain no dimension, no stress and no material: a rectangle is exactly 3/2 whatever its size, a diamond exactly 2, a circle 16/3π. The spread is the argument. An I-section keeps only 13 per cent in reserve past first yield, because nearly all its material is already at the extreme fibre and there is nothing further in to recruit; a diamond keeps 100 per cent, because most of its material is near the middle and doing very little elastically. So the section shapes that are best at elastic bending are the ones with the least left afterwards, which is exactly backwards from the way the reserve is usually described.

What is left after the first fibre yields

The elastic section modulus stops at the moment the outermost fibre reaches yield. Nothing else in the section has, so it goes on taking load — and how much more it takes turns out to be a property of the shape alone, with no dimension, no stress and no material anywhere in the answer.

sections · Shape factor

Deliberately the wrong shape

Concrete in compression follows a curve, and no design office has ever integrated it. Every code in the world replaces it with a rectangle of reduced depth and reduced intensity, and the answer is right to a fraction of a per cent — not because the shapes are similar, which they visibly are not, but because a bending calculation only ever asks a stress distribution two questions.

sections · Stress block

The section calculation with no formula in it

Every ordinary section result is a closed form, and each was derived once for one arrangement of material. Slice the section instead, give each strip the strain a curvature puts it at, and move the neutral axis until the axial force balances — and the same twenty lines answer for a cracked section, a confined one, a prestressed one and a composite one, having been told nothing about any of them.

sections · Fibre model

Where the steel is, not how much of it

A section in bending resists a moment with a couple, and a couple is a force times a distance. The force is bought — it is an area of steel at a stress. The distance is free, decided by where the bars were put, and it is the variable almost nobody optimises because it does not appear on an order.

sections · Lever arm

The axis that moves when the section yields

An elastic section bends about its centroid. A fully plastic one bends about the axis that halves its area, and for anything symmetric those are the same line — which is why the distinction is almost never met. For a tee they are a fifth of the depth apart, and three things follow that the elastic calculation gives no warning of.

sections · Equal-area axis

The axis a column buckles about

A strut buckles about the axis with the smallest second moment of area, and for a section with no axis of symmetry that axis is neither of the two on the drawing. An angle used as a strut is 2.45 times weaker than the number a designer reads off its own dimensions.

sections · Principal axes

The wide side goes inside

A crane hook's section is a trapezoid with its broad face towards the centre of curvature, and that is not a casting convenience. Turn the same section round — same area, same depth, same moment — and the stress at the fibre that breaks rises by thirty-nine per cent. The shape is doing two things at once, and only one of them is in a straight beam's arithmetic.

sections · Curved beam

The eccentricity at right angles to the drawing

A bracket's load stands off the plane of its welds as well as being offset within it, and the second eccentricity produces a completely different object — bending about an axis through the group rather than torsion about a point in it. The weld line has no compression zone to argue about, so its neutral axis is its own centroid, and the whole length works.

connections · Weld group

Classified by a gradient it does not have

A web in bending is the one plate whose buckling coefficient cannot be looked up. It depends on the stress gradient, the gradient depends on where the neutral axis is, and the neutral axis depends on how much of the web the coefficient has just taken away — so the answer is a fixed point, and the calculation everyone does is its first term.

stability · Plate buckling

Named alongside it

The objects these essays reach for when they reach for this one.

Second moment of areaSection modulusPlane sectionsCentroidStress blockBending stressComposite actionLever armShape factorFirst moment of areaFree bodyMoment-curvature

All concepts