Structural Engineering & Statics
where the load goes
Concept

Sliding bearing — where it appears

A support that carries vertical load while allowing horizontal movement across a low-friction surface. It is never frictionless, so it applies a horizontal force to whatever it sits on, and that force reverses direction with the movement.

Named by 4 essays across 2 fields — each of them below, with the objects they name alongside it.

The bearing that is drawn as a roller. The horizontal force a sliding bearing delivers, against the vertical load it is carrying, with its coefficient of friction on the same picture. The coefficient is not a constant: PTFE's falls as the contact pressure rises, and the standard fit is μ = 1.2/(10 + σ), so the bearing drawn is at 30.0 N/mm² and μ = 0.030 while the same bearing at a fifth of the load is at 0.075 — 2.5 times as much. The force curve is therefore strongly non-linear: a fifth of the load gives 50% of the force. Two readings follow and only one of them is usually taken. The largest force is at full load, 108 kN, and that is what the pier is designed for. The largest nuisance is at light load, where 54 kN of friction is 39% of the 140 kN of wind the bearing was put there to release the structure from. Cold makes it worse again: below about −5 °C the same bearing delivers 216 kN. A roller symbol on a drawing means this, and it is a pair of load cases rather than one, because friction opposes whichever way the deck happens to be going.

The roller that is not a roller

A sliding bearing is drawn as a roller and detailed as a sheet of PTFE, and it delivers a horizontal force of a few per cent of whatever it is carrying. The coefficient everybody quotes is the one at full design pressure, and PTFE's coefficient rises as the pressure falls — so the bearing is at its freest exactly where nobody checks it.

connections · Bearing friction The reaction lies inside the cone, so the block stands. A block of 48 on a plane at 22°, against a coefficient of friction of 0.6. Resolving across and along the plane gives a normal force of 44.5 and a friction demand of 18.0, against a capacity of μN = 26.7 — a ratio of 0.67. Added together the two make one contact reaction leaning 22.0° from the normal, and the admissible reactions fill a cone of half-angle arctan μ = 31.0°. Equilibrium is possible exactly when the demanded reaction lies inside that cone, which here it does. The weight enters neither the cone nor the lean: a block of any weight on this slope leans its reaction by the same 22.0°, which is why the angle of repose is a material property and the size of a heap of sand is not.

The area that is not in the equation

Friction is proportional to the force pressing two surfaces together and independent of how large they are, which sounds like an approximation and is not. The area is absent because the contact that carries the load is a tiny fraction of the contact that is drawn, and that fraction grows in exact proportion to the load.

equilibrium · Friction The pier grips, gives, and grips again. A sliding bearing carrying 3000 kN on a pier head of 20 kN/mm, dragged by a deck expanding at 1.7 mm an hour, with a static coefficient of 0.05 and a kinetic one of 0.03. The force in the pier climbs while the bearing grips, reaches 150 kN, and falls in a fraction of a second to 30 kN: the pier springs back under only the kinetic friction, overshoots the 90 kN that friction would hold it at, and grips again. The swing is 120 kN — 2.00 times the 60 kN between the two coefficients — and the pier head jumps 6.00 mm each time, three times in 12 hours.

The pier that moves in jumps

A sliding bearing whose static friction is larger than its kinetic friction does not release a slow thermal movement as a drift. It grips, gives and grips again, and each time the force in the pier swings by twice the difference between the two coefficients — whatever the pier is made of.

equilibrium · Friction Same deck, same load, and two pier forces. A deck bearing on a pier of 20 kN/mm with μ = 0.03, taken to the same final state two ways: the deck moves 4 mm over the pier, and the bearing's load rises from 2000 to 4000 kN. Moved first, while the bearing carries 2000 kN, the pier force reaches the limit of 60 kN and the bearing slides for the rest of the movement; the load arriving afterwards raises the limit and changes nothing, and the pier is left carrying 60 kN. Loaded first, the limit is 120 kN before the deck moves, the bearing grips throughout, and the pier carries 80 kN. Both states are at the same displacement under the same load, and both satisfy equilibrium and the friction bound; the order is the only difference, and it appears in neither.

The order the loads arrived in

Statics allows a contact with friction a whole range of forces and has no way to choose between them. A real structure does choose, and what it chooses by is the order in which things happened to it — so the force in a pier under a sliding bearing is a record of its history, not a function of its loads.

equilibrium · Friction

Named alongside it

The objects these essays reach for when they reach for this one.

FrictionCoefficient of frictionThermal movementBearingContact pressureEnergy dissipationFree bodyRestraintStick-slipAngle of reposeArticulationConstruction sequence

All concepts