Structural Engineering & Statics
where the load goes
Concept

Self-locking — where it appears

The condition in which friction alone holds a wedge or a screw in place whatever the load, because the interface angle is inside the friction cone. It makes a mechanism irreversible without an applied force, and it fails as soon as vibration or lubrication reduces the friction.

Named by 3 essays across 2 fields — each of them below, with the objects they name alongside it.

The reaction lies inside the cone, so the block stands. A block of 100 on a plane at 15°, against a coefficient of friction of 0.35. Resolving across and along the plane gives a normal force of 96.6 and a friction demand of 25.9, against a capacity of μN = 33.8 — a ratio of 0.77. Added together the two make one contact reaction leaning 15.0° from the normal, and the admissible reactions fill a cone of half-angle arctan μ = 19.3°. Equilibrium is possible exactly when the demanded reaction lies inside that cone, which here it does. The weight enters neither the cone nor the lean: a block of any weight on this slope leans its reaction by the same 15.0°, which is why the angle of repose is a material property and the size of a heap of sand is not.

The force that is whatever it needs to be

Every other force in statics has a value the equations produce. Friction has an inequality instead, so it takes whatever value equilibrium demands and the bound only ever says no — which means a problem with friction in it has a range of answers rather than one.

equilibrium · Friction The reaction lies inside the cone, so the block stands. A block of 48 on a plane at 22°, against a coefficient of friction of 0.6. Resolving across and along the plane gives a normal force of 44.5 and a friction demand of 18.0, against a capacity of μN = 26.7 — a ratio of 0.67. Added together the two make one contact reaction leaning 22.0° from the normal, and the admissible reactions fill a cone of half-angle arctan μ = 31.0°. Equilibrium is possible exactly when the demanded reaction lies inside that cone, which here it does. The weight enters neither the cone nor the lean: a block of any weight on this slope leans its reaction by the same 22.0°, which is why the angle of repose is a material property and the size of a heap of sand is not.

The area that is not in the equation

Friction is proportional to the force pressing two surfaces together and independent of how large they are, which sounds like an approximation and is not. The area is absent because the contact that carries the load is a tiny fraction of the contact that is drawn, and that fraction grows in exact proportion to the load.

equilibrium · Friction Nine-tenths of a tightening torque stretches nothing. Where the torque applied to the nut of an M20 grade 10.9 bolt goes, against the coefficient of friction in its thread and under its nut, taken as equal. The bottom band is the thread's lead — the only part of the work that stretches the bolt — the middle band is friction in the thread and the top band is friction under the nut. At μ = 0.14 the lead takes 11% of the torque, the thread 39% and the nut face 50%. At μ = 0.06 the lead's share is 22% and at 0.24 it is 6%, so a coefficient nobody measured decides how much of a specified torque arrives in the bolt as preload.

The torque that goes into the thread

A preload specified as a torque is a preload specified through two coefficients of friction that nobody measures. Nine-tenths of the torque on a bolt is spent turning against its own thread and the face of its nut, so a change in the grease moves the clamping force by half — and the one method that escapes it does so by yielding the bolt on purpose.

connections · Slip-critical

Named alongside it

The objects these essays reach for when they reach for this one.

FrictionSlip resistanceAngle of reposeCoefficient of frictionEquilibriumFree bodyOverturningPreloadBolt tensionConnectionContact pressureDuctility

All concepts