Structural Engineering & Statics
where the load goes
Concept

Bearing pressure — where it appears

The stress a foundation or a base plate delivers to what it sits on, distributed over whatever part of the base is still in contact. It is distributed over whatever part of the base is still in contact, so once the resultant leaves the kern the effective area shrinks and the peak pressure climbs faster than the load.

Named by 7 essays across 4 fields — each of them below, with the objects they name alongside it.

Weight is the only thing holding it down. A body 2.5 m wide and 6 m tall weighing 120 kN, under a wind pressure of 1 kN/m². The wind delivers 48 kN and an overturning moment of 144 kNm about the leeward toe; the weight restores 150 kNm, a factor of 1.04. The resultant lands 1.20 m from the centre against a middle third of ±0.42 m, so the base is lifting over 2.35 m of its width.

Weight is the only thing resisting it

A structure that is strong enough everywhere can still be blown over, and nothing in its material properties has any part in whether it is. The whole answer is a weight and a width — and the failure begins long before anything tips, at the moment one edge stops pressing down.

equilibrium · Overturning The middle third, computed. The kern of a 400 × 600 mm rectangle, computed by asking, for every direction, how far the resultant can move before the far face would be pulled. It reaches ±100.0 mm vertically and ±66.7 mm horizontally, which are h/6 and b/6 exactly, and the region between is a rhombus rather than the ellipse the two numbers suggest — a resultant on a diagonal has less room than either axis allows.

The middle third

A material that cannot be pulled imposes a condition on where the load may land, and the condition is a region rather than a point. For a rectangle it is the famous middle third; for every other section it is a shape nobody quotes, and one ordinary section's is nearly twice as generous as the rule allows.

sections · Kern Five loads behind one wall, and the water is the biggest. The horizontal pressure on a 6 m wall retaining soil at 18 kN/m³ with a friction angle of 30°, a surcharge of 10 kPa and the water table 2 m down, drawn once as the profile the wall feels and then once per term. The terms are surcharge 20.0 kN/m at 3.00 m, soil above water 12.0 kN/m at 4.67 m, soil at the water table 48.0 kN/m at 2.00 m, submerged soil 27.2 kN/m at 1.33 m, water 78.5 kN/m at 1.33 m, and they sum to 185.7 kN/m — matched to 7e-8 by integrating the drawn profile numerically. The largest single term is the water, at 78.5 kN/m: water has no shear strength, so its coefficient is exactly one where the soil's is 0.333, and it acts on top of the soil's effective stress rather than instead of it. The combined resultant sits at 1.90 m above the base, 0.317 of the height rather than the third point at 2.00 m that a pure triangle would give.

The load that depends on what carries it

Every other load in this collection is a number the structure is given. Retained soil is not — it pushes with a fraction of its own weight, and the fraction is decided by how far the wall moves. Six millimetres of retreat on a six-metre wall takes a third off the load, and being held still puts it back.

equilibrium · Lateral pressure The middle third, computed. The kern of a 300 × 600 mm rectangle, computed by asking, for every direction, how far the resultant can move before the far face would be pulled. It reaches ±100.0 mm vertically and ±50.0 mm horizontally, which are h/6 and b/6 exactly, and the region between is a rhombus rather than the ellipse the two numbers suggest — a resultant on a diagonal has less room than either axis allows.

The strength thrown away on purpose

Masonry, concrete and soil are all analysed as though they had no tensile strength whatever. Each of them has some. The decision to set it to zero is the single most consequential modelling assumption in the subject, it is safe for one kind of check and unsafe for another, and almost nothing that uses it says which.

materials · No tension Weight is the only thing holding it down. A body 1.6 m wide and 4.5 m tall weighing 22 kN, under a wind pressure of 1 kN/m². The wind delivers 2 kN and an overturning moment of 4 kNm about the leeward toe; the weight restores 18 kNm, a factor of 4.35. The resultant lands 0.18 m from the centre against a middle third of ±0.27 m, so the base is still wholly in bearing.

Whether it tips or slides

A free body pushed sideways has two ways of leaving, and which one it takes is decided before any load is known. The condition is a width divided by a height set against a coefficient of friction, and the weight, the wind pressure and the depth of the body all cancel out of it.

equilibrium · Overturning A base plate, and when the bolts start working. A 550 × 450 mm plate carrying 900 kN and 140 kN·m, so the resultant sits 155.56 mm from the centre against a kern of 91.67 mm. The plate is in partial contact: bearing over 358.33 mm at a peak of 11.16 N/mm², with the holding-down bolts carrying 0 kN. The plate lifts at 82.5 kN·m and crushes at 192.95 kN·m, and the bolts are not needed until 247.5 kN·m.

The pinned base that is not pinned

A column base drawn as a pin is a plate bearing on grout, and a plate in contact over its whole length resists rotation whether anybody wanted it to or not. The stiffness it delivers depends on the axial load, so the assumption is one a frame can leave and re-enter as its loads change.

stability · Sway stability The push that tips it, in every direction. The tipping push in each plan direction, drawn as a distance from the centre, for a 6000 kN body with its weight 15 m up and the push at 18 m. On rigid ground the curve is the hull's: weakest along the axes at 1333 kN. On four equal pads it shrinks, and more toward the corners. With the pads as built — stiffnesses 20000, 20000, 8000, 20000 kN/m — it is no longer symmetric: the weakest direction is 15°, on the soft pad's side, at 1039 kN.

It tips inside its own hull

On rigid ground a body tips when its resultant reaches the edge of its base, and how stiff its supports are has nothing to do with it. On pads that settle, the body leans as it is pushed, the lean moves its weight, and the push that tips it falls by one number a site engineer already has: settlement times the height of the weight, over the square of the half-width. Toward a corner the loss doubles, and one soft pad makes the weakest direction one nobody checks.

equilibrium · Overturning

Named alongside it

The objects these essays reach for when they reach for this one.

EccentricityKernOverturningFactor of safetyFree bodyUpliftEquilibriumFrictionRestraintSelf-weightThrust lineBase plate

All concepts