Structural Engineering & Statics
where the load goes
How this site is made

The figure library — page 4

Every picture here is generated from code. This page lists the generator families, how many essays call each one, and how many separate drawings each has produced. Page 4 of 7, parallel-axis to response-spectrum.
Moving the flanges apart. The second moment of area of an I-section against its depth, with the flange and web areas held constant. The growth is close to quadratic, because the parallel-axis term dominates everything the flanges contribute about their own centres.

parallel-axis

5 essays The bearing is one length and the web is loaded over another. A load applied over a stiff bearing of 100 mm on the flange of a girder with a 1200 × 8 mm web. The flange bends under it and the yield lines that form spread the load along the web over 559 mm — 5.6 times the bearing, and 82% of the yield resistance is that spread rather than the bearing. The effective length is not a decision anybody made: it is what the flange's own bending stiffness against the web's own strength works out to.

patch-load

6 essays A pile has no length until the ground gives it one. Deflection, bending moment and soil reaction down a 0.6 m pile carrying 150 kN at a free head, in ground whose modulus grows by 0.005 N/mm³ per millimetre of depth. The one length in the problem is T, the fifth root of EI over n_h, which is 1.89 m here; the head moves 20.5 mm, the worst moment of 219 kNm is at 2.50 m — 1.32 T — and below about four T nothing happens at all. The classical coefficients come out of the finite differences rather than a table: 2.430 against Matlock and Reese's 2.435, and 0.772 against their 0.772.

pile-lateral

3 essays The worst force in a pile is not at the top of it. A 0.6 m pile 24 m long through ground that is settling, carrying 800 kN at its head. Above the neutral plane the soil moves down past the shaft and the friction acts downward, so the axial force grows with depth; below it the friction acts upward in the ordinary way and the force falls again to the 300 kN the base takes. The maximum is 1282.87 kN at 13.78 m — 1.60 times the load applied, and it is at a depth where nothing is applied, nothing is connected and nothing can be inspected. A pile section chosen for the head load is under-sized by that factor over the middle third of its length.

pile-transfer

3 essays Two centres, and the distance between them is a torque. A storey 30 by 18 m with its walls drawn heavy, pushed in one direction by 1000 kN. The force acts through the centre of mass and the storey turns about the centre of rigidity — the stiffness-weighted centroid of the walls, at x = 15.0 m — and the distance between the two is an eccentricity of 0.00 m before the 5% that has to be assumed anyway. The table below the plan splits each wall's force into its direct share and its torsional one. Torsion relieves the walls near the centre of rigidity and loads the far ones, so the wall in trouble is not the wall carrying the most: west wall is asked for 8% more than its direct share, and the walls at right angles to the push carry 19 kN each with nothing applied along them at all.

plan-rigidity

2 essays Where plane sections stop staying plane. Strain across a cut face at four span-to-depth ratios, with the straight line the theory assumes drawn faintly behind. For a slender beam the two coincide; for a beam as deep as its span the real distribution is nothing like a straight line, and beam theory has no claim on it.

plane-sections

11 essays The collapse mechanism of a propped cantilever. A collapse mechanism, with the hinge position found by searching rather than quoted. Every position gives an upper bound on the collapse load; the lowest is 7.29, at a hinge 58.6 per cent along, which is a coefficient of 11.657 times Mp over the square of the span.

plastic-mechanism

10 essays A 8 mm plate, and the width it can be. The elastic critical stress of a plate in compression against its width, with the yield stress drawn across it. Below 370 mm the plate reaches yield before it buckles; above it the plate ripples first, and the fraction of the width still carrying load falls away — at 700 mm only 47 per cent of it is still working.

plate-buckling

15 essays A portal frame swaying under 20 kN. A portal frame pushed sideways, solved by the stiffness method because statics cannot divide the load between two columns. The base shears come out at 10.0 and 10.0 and add to the applied 20; the peak moment is 22.2. The sway is drawn hugely exaggerated, and the moment diagram is plotted on each member's tension face.

portal-sway

10 essays Three paths out of the same critical load. Load against sideways movement past the critical load, for three systems whose critical loads are identical. The stable one climbs, so a real structure with a small crookedness reaches nearly the full load and keeps going. The unstable one falls symmetrically, so the imperfect structure has a maximum below the critical load and it matters not at all which way it leans. The asymmetric one falls one way and climbs the other, so the direction of the imperfection decides everything. All three are drawn at an imperfection of 0.02 radians.

post-buckling

6 essays Two triangles that cross zero, and a block that does not. Stress across a 300 × 700 mm section at each stage, compression positive. The prestress alone gives -6.33 MPa at the top and 20.61 at the bottom; at transfer, with only self-weight on it, the top is at -2.47 MPa and in service the section runs from 7.61 to 3.82 MPa — compression everywhere. The same beam with no prestress reaches -12.67 MPa at the bottom fibre, which is 4.2 times what the concrete can hold.

prestress-section

10 essays Loaded straight down, and moving sideways. An equal angle with a moment applied about the horizontal axis. Its principal axes lie at 45.0° to the drawn ones, so the neutral axis runs at -30.6° rather than horizontally, and the section moves 59% as far sideways as it moves down. The product of inertia that causes it is -1.066 × 10⁶ mm⁴, and it is zero for every section drawn in this field until now.

principal-axes

5 essays Prying action in a tee stub. A tee stub pulled by its web with 100 kN per bolt. The 20 mm flange is in the one-hinge regime, so the prying force at the flange tip is 50.63 kN and the bolt carries 150.63 kN — 1.51 times what was applied. The flange stops prying entirely at 26.97 mm thick, and collapses on its own at 110 kN.

prying-tee

9 essays A check made on a perimeter, not on a section. One bay of a flat slab, 7.2 m square, on a 400 × 400 mm column. The heavy closed line is the control perimeter, 2d from the column face with its corners rounded at that radius — 4427 mm long against 1600 mm round the column itself. The shaded area inside it delivers no shear across it and is subtracted from the load; everything outside arrives through the perimeter. At 12 kN/m² that is 604 kN across 4427 × 225 mm, a shear stress of 0.606 N/mm² against a resistance of 0.658.

punching-perimeter

2 essays The curve a structure has, before any earthquake is chosen. Base shear against roof displacement for a eight-storey frame pushed with a triangular load pattern. It is elastic to 1994 kN, where the first storey reaches its shear capacity, and flattens as each of the others follows — 7 yield events in the order 3, 4, 2, 1, 5, 6, 7. The idealised bilinear curve is drawn through it by equal areas, which puts the yield displacement at 70 mm — nearly three times the first yield, and the reason a ductility quoted against first yield means nothing.

pushover-curve

3 essays Four guesses at one buckling mode. A pin-ended column, with four assumed shapes and the load each of them gives. The reference is a ten-term Ritz expansion solved as an eigenvalue problem, at 9.8696 EI/L² — which is π², as it must be. a half sine gives 9.870, its own sag shape gives 9.882, a mid-span sag gives 10.000, a parabola gives 12.000. Every one of them is high and none of them is low, because an assumed shape is a constraint on the column and a constraint can only stiffen it.

rayleigh-strut

5 essays Where the peak moment goes when a restraint is added. The same uniformly loaded beam with three sets of restraints, and the bending moment in each. Adding restraint moves moment from mid-span to the supports and lowers the peak — but only the first case can be solved by statics.

redundant-beam

13 essays The response spectrum of that record, at one damping ratio. The peak pseudo-acceleration of a single-degree-of-freedom structure against its natural period, for the record above, at 5% damping. Each curve is 44 complete time integrations — one structure per point. At zero period the structure is rigid and rides the ground, so the curve starts at the peak ground acceleration of 3.5 m/s²; it peaks at 7.07 m/s² at a period of 0.37 s, an amplification of 2.02.

response-spectrum

10 essays