Structural Engineering & Statics
where the load goes
Concept

Mohr circle — where it appears

Every plane through a point, drawn as one circle in stress space, so the principal stresses are its ends and their directions are read off its diameter. It turns a question about which plane is worst into a question about a radius, and it is the whole of why an uncracked prestressed web needs no fitted expression.

Named by 3 essays across 3 fields — each of them below, with the objects they name alongside it.

One criterion inside the other, touching at six points. The two yield criteria in principal stress space with the third principal stress zero, both normalised by the yield stress. Von Mises is the ellipse — σ₁² − σ₁σ₂ + σ₂² = f_y², which is a circle seen at an angle — and Tresca is the hexagon inscribed in it, touching at the six points where one principal stress is zero or the two are equal. Everywhere else Tresca is the smaller, by up to 15.5 per cent, and the widest gap is at pure shear, where σ₁ = −σ₂ and the two answers are 205 and 178 N/mm². The ratio there is exactly 2/√3, computed rather than quoted, and it is the whole reason a web is checked against f_y over root three.

The shear strength nobody measured

Every steel web in a design check is checked against the yield stress divided by the square root of three, and no test produced that number. It is a consequence of a decision about what makes a metal yield, and the alternative decision gives a different answer by fifteen per cent.

materials · Yield criterion Prestress buys shear as a square root, not as a sum. The shear stress an uncracked web can take before the principal tension reaches the concrete's tensile strength, against the axial compression the prestress put there. With no prestress it is 1.35 N/mm², the tensile strength itself, because pure shear has a principal tension of exactly its own magnitude at forty-five degrees. Adding compression gives √(f_ct² + σ_cp·f_ct), which is a square root and therefore flattens: the first newton of prestress is worth far more than the last. At the 7.14 N/mm² drawn the limit is 3.39 N/mm², a gain of 2.51, and doubling the prestress from there takes it only to 4.59. The straight line is what a rule that simply added the two strengths would have promised.

The crack that never reached forty-five degrees

Every shear expression for reinforced concrete is a curve fitted to tests, because a cracked section has no free body worth drawing. An uncracked prestressed web has one — a single point, a Mohr's circle and a principal tension — and it is the only shear check in the subject that is derived rather than measured.

internal-forces · Prestressed shear One point, every plane through it, one circle. A point carrying 180 N/mm² across one face, 90 across the other and 40 of shear. As the plane is turned, the pair (σ, τ) runs round a circle of radius 60.2 centred at 135.0 — and it goes round at twice the rate the plane does, which is the part always misremembered and the part that makes the picture work. The principal stresses are 195.2 and 74.8, on planes 20.8° from the face the 180 acts on; the largest shear on any plane is 60.2, exactly the radius, and it sits 45° from those — which is 90° round the circle. The von Mises stress that ranks this state against any other is 170.6.

The circle nobody draws

A plane stress state has three principal stresses and the third is zero. When the two on the drawing share a sign, the largest shear in the state involves the one that is not there — and the circle a designer has drawn is not the circle that governs.

sections · Principal stress

Named alongside it

The objects these essays reach for when they reach for this one.

Principal stressConfinementHydrostatic stressTrescaVon misesYield criterionCrackingDeviatoric stressDuctilityEquivalent stressFree bodyInteraction diagram

All concepts