Structural Engineering & Statics
where the load goes
Concept

Boundary conditions — where it appears

What a structure is attached to, stated as conditions the solution has to satisfy at its edges. They are integration constants rather than forces, they decide the answer as completely as the loading does, and a boundary condition that depends on the load is what makes superposition stop working.

Named by 4 essays across 2 fields — each of them below, with the objects they name alongside it.

The same curve, computed twice and from opposite ends. A cantilever of 6 m, with its deflected shape drawn from a double integration of M/EI and the bending moment of its conjugate beam drawn on top of it. The conjugate is the same span carrying M/EI as a load, with its supports transformed — a real fixed end becomes a free end and a real free end becomes a fixed one, because a fixed end has no slope and no deflection and the conjugate therefore needs no shear and no moment there. The two curves agree to 4.7e-6 of the largest deflection, which is the trapezium rule and not the method. The largest deflection is 36.00 mm against the closed form's 36.00. The reaction of the conjugate beam is -9.000 milliradians, which is the real beam's rotation at that support — so the whole of a slope calculation is one reaction.

The beam whose moment is a deflection

A beam's bending moment is the second integral of its load. Its deflection is the second integral of M/EI. They are the same problem, so a deflection can be found by loading a fictitious beam with M/EI and asking a statics question — and the only thing to remember is the supports, which are not remembered but derived, one boundary condition at a time.

deflection · Conjugate beam Two answers added, and the answer to the two together, drawn on top of each other. A 8 m beam under a 60 kN point load at mid-span (152.38 mm), under 12 kN/m of uniform load (152.38 mm), and under both at once (304.76 mm). The sum of the first two is 304.76 mm, and the residual between it and the third is zero — not small, zero, to the last bit of the arithmetic. That exactness is not a numerical accident: the governing equation is linear in the load, so the response is a linear operator applied to it, and a linear operator distributes over addition by definition. Every calculation that adds one load case to another is standing on that one line.

The addition everything else rests on

Influence lines add, the unit-load method adds, moment distribution adds, load combinations add, and a stiffness matrix is linear by construction. All of it stands on one sentence with three hypotheses in it — and when they fail, two of the failures point in opposite directions.

deflection · Superposition A 10 mm plate, and the width it can be. The elastic critical stress of a plate in compression against its width, with the yield stress drawn across it. Below 462 mm the plate reaches yield before it buckles; above it the plate ripples first, and the fraction of the width still carrying load falls away — at 900 mm only 46 per cent of it is still working.

The coefficient that is not four

A plate's buckling stress carries a coefficient that looks like a constant and is not. It is 4 for an internal element, 0.43 for an outstand and 23.9 for a panel in shear — and the width a 10 mm plate may be runs from 152 mm to 1,130 across that range.

stability · Plate buckling The coefficient is an envelope, and its scallops are whole half-waves. The plate buckling coefficient against aspect ratio α = a/b. Each faint branch is one half-wave count m: k = (m/α + α/m)², a curve whose own minimum is exactly 4 at α = m. The plate takes whichever branch is lowest, so the answer is the bold envelope — four touching 4 at α = 1, 2, 3 and 4, with cusps between them at α = √(m(m+1)) = 1.41, 2.45, 3.46, 4.47, where the plate is indifferent between m and m+1 half-waves. The first cusp reaches k = 4.50 and every later one is lower — 4.17, 4.08, 4.05. Past α = 1 the envelope never exceeds 4.49, which is why the length of a plate drops out of a formula that is otherwise entirely geometry.

Four was never a fact about plates

The coefficient every plate calculation starts from is quoted as 4, derived nowhere and remembered by everyone. It is the minimum of a quantity that has nothing to do with plates in it — and what the plate supplies is not the four but the restriction that produces the scallops around it.

stability · Plate buckling

Named alongside it

The objects these essays reach for when they reach for this one.

Free bodyBuckling coefficientCritical stressEffective widthPlate bucklingBuckled mode shapeConjugate beamCrackingCurvatureDeflectionDeterminacyDuality

All concepts