Structural Engineering & Statics
where the load goes
Generator

Five loads behind one wall, and the water is the biggest

Rendered here at the parameters it defaults to, with every essay that calls it — which is the same list as the blast radius of changing it.
Five loads behind one wall, and the water is the biggest. The horizontal pressure on a 6 m wall retaining soil at 18 kN/m³ with a friction angle of 30°, a surcharge of 10 kPa and the water table 2 m down, drawn once as the profile the wall feels and then once per term. The terms are surcharge 20.0 kN/m at 3.00 m, soil above water 12.0 kN/m at 4.67 m, soil at the water table 48.0 kN/m at 2.00 m, submerged soil 27.2 kN/m at 1.33 m, water 78.5 kN/m at 1.33 m, and they sum to 185.7 kN/m — matched to 7e-8 by integrating the drawn profile numerically. The largest single term is the water, at 78.5 kN/m: water has no shear strength, so its coefficient is exactly one where the soil's is 0.333, and it acts on top of the soil's effective stress rather than instead of it. The combined resultant sits at 1.90 m above the base, 0.317 of the height rather than the third point at 2.00 m that a pure triangle would give.

Five loads behind one wall, and the water is the biggest. The horizontal pressure on a 6 m wall retaining soil at 18 kN/m³ with a friction angle of 30°, a surcharge of 10 kPa and the water table 2 m down, drawn once as the profile the wall feels and then once per term. The terms are surcharge 20.0 kN/m at 3.00 m, soil above water 12.0 kN/m at 4.67 m, soil at the water table 48.0 kN/m at 2.00 m, submerged soil 27.2 kN/m at 1.33 m, water 78.5 kN/m at 1.33 m, and they sum to 185.7 kN/m — matched to 7e-8 by integrating the drawn profile numerically. The largest single term is the water, at 78.5 kN/m: water has no shear strength, so its coefficient is exactly one where the soil's is 0.333, and it acts on top of the soil's effective stress rather than instead of it. The combined resultant sits at 1.90 m above the base, 0.317 of the height rather than the third point at 2.00 m that a pure triangle would give.

13 essays call earth-pressure. The drawing above is what it returns with no arguments at all; every call below passes it something, because a placement that passes nothing draws whichever member of the family the generator happens to default to rather than the one its essay argues about.

Where it is called

Changing this generator changes every one of these figures.

Five loads behind one wall, and the water is the biggest. The horizontal pressure on a 6 m wall retaining soil at 18 kN/m³ with a friction angle of 30°, a surcharge of 10 kPa and the water table 2 m down, drawn once as the profile the wall feels and then once per term. The terms are surcharge 20.0 kN/m at 3.00 m, soil above water 12.0 kN/m at 4.67 m, soil at the water table 48.0 kN/m at 2.00 m, submerged soil 27.2 kN/m at 1.33 m, water 78.5 kN/m at 1.33 m, and they sum to 185.7 kN/m — matched to 7e-8 by integrating the drawn profile numerically. The largest single term is the water, at 78.5 kN/m: water has no shear strength, so its coefficient is exactly one where the soil's is 0.333, and it acts on top of the soil's effective stress rather than instead of it. The combined resultant sits at 1.90 m above the base, 0.317 of the height rather than the third point at 2.00 m that a pure triangle would give. Equilibrium

The load that depends on what carries it

Every other load in this collection is a number the structure is given. Retained soil is not — it pushes with a fraction of its own weight, and the fraction is decided by how far the wall moves. Six millimetres of retreat on a six-metre wall takes a third off the load, and being held still puts it back.

 A basement is a boat. A 20 by 30 m substructure dug 6 m into ground whose water table stands 2 m down. The head on the underside of the base slab is 4.0 m, so the pressure there is 39.2 kN/m² over the whole plan — 23.5 MN of it, pushing upward. Nothing about the structure changes that number. What resists it is weight: 18.7 MN of concrete and whatever is built above, giving a factor of 0.80. The structure floats if the water reaches 2.82 m below the ground, and a base slab alone would have to be 1.64 m thick to hold it down. Equilibrium

A basement is a boat

Every load in this collection presses down and is resisted by strength. Hydrostatic uplift presses up, is resisted by weight, and does not care what is built on it — so the check contains no material property at all. It is a ratio of two weights, and one of them is water.

 A tank grows without limit; a silo stops. Vertical pressure against depth in a 8 m silo of a solid weighing 9 kN/m³, beside the straight line a liquid of the same weight would have produced. The free body is a slice: its own weight in, the wall friction out, and the friction is μK times the vertical pressure that generates it. The result saturates at γR/μK = 89 kN/m² and reaches 63% of it at one characteristic depth, R/μK = 9.9 m. At the base the pressure is 85 kN/m² against a liquid's 270 — 69% less — and the wall has taken 69% of the stored weight down with it. The exponent is the capstan's, and for the same reason. Equilibrium

The pressure that stops growing

A tank of liquid presses harder the deeper it gets, without limit. A silo of grain does not. Wall friction carries part of the weight, the pressure that generates the friction is proportional to the pressure being carried, and the equation that follows is the one that describes a rope round a bollard.

 Two drawings of one deck, and they are not the same structure. A 112 m viaduct on five supports, articulated two ways. Above, the fixed point is at the left abutment: the far end has to be given 45 mm of movement, and the friction of every sliding bearing runs one way, so the fixed support takes 660 kN before any wind or braking is applied. Below, the fixed point is at the middle pier: the largest joint halves to 22 mm and the friction now cancels across the fixed point, leaving 0 kN. The movement arrows are drawn at 900 times the scale of the deck, because a 45 mm movement on a 112 m span is thinner than the line the deck is drawn with. Nothing about the deck, the loads or the ground has changed between the two. Structural form

Where the structure is allowed to move

One drawing decides how big every movement joint on a bridge is and where every horizontal force goes, it takes an afternoon, and it appears on no calculation sheet. Move the fixed point from an abutment to the middle pier and the largest joint halves and the horizontal force on that support drops from the whole of the friction to none of it.

 A bearing capacity is a mechanism, and here it is. Prandtl's collapse mechanism under a 3.0 m footing in a soil of 32° friction. A rigid wedge is driven down with the footing at 61° to the horizontal; a fan of radial shear turns the stress through exactly ninety degrees on a logarithmic spiral whose growth rate is tanφ; and a passive wedge at 29° has to be pushed up and out of the way. Nothing here is empirical — every angle is a function of φ alone — and the mechanism reaches 15.9 m from the centre, which is 10.6 times the footing's half width. That is why two footings closer together than about four widths do not have separate bearing capacities. Equilibrium

The ground is a mechanism

Bearing capacity is met as a formula with three terms and a table of coefficients, and that presentation hides what it is. Underneath is a plastic collapse mechanism — a rigid wedge, a fan of radial shear on a logarithmic spiral, and a passive wedge that has to be pushed up and out of the way — and every coefficient in the table is a property of that one drawing.

 The prop load is decided by the digging, not by the hole. Prop forces in a 12 m excavation propped at 3 levels, with the force each prop reaches at any stage of the sequence drawn thick and the force the finished arrangement gives it drawn thin. The pale dots are the individual stages. The middle prop reaches 214 kN while the dig is at 9.5 m and finishes at 88 — a factor of 2.44 between the two, and the larger one is not in the final analysis anywhere. Terzaghi and Peck's apparent pressure diagram, a rectangle of 49.4 kN/m², reproduces the total of the staged maxima to 2% — which is what it is: an envelope of measured prop loads, back-figured into a pressure, and a shape nothing on a wall is ever loaded with. Structural form

Every prop has its own worst day

A braced excavation has no finished state worth analysing. It is dug in stages, a level of props goes in at each stage, and a prop's force is largely fixed the moment it is installed — so the force to design it for is the largest it sees during a sequence that appears on no calculation sheet, and which for the middle prop here is nearly two and a half times what the finished arrangement gives.

 The lining that carries less for being weaker. Bending moment and hoop thrust in a circular lining, against the lining's own bending stiffness, both as fractions of the free-ring values. The ground arrives already stressed — 500 kPa vertically and 300 horizontally at K₀ = 0.6 — and the difference between them tries to squash the hole into an ellipse. A lining stiff enough to refuse absolutely collects the whole distortion pressure, p₂R²/3 = 300 kNm/m; one flexible enough to go with the ground collects nothing, because there is no curvature change left to resist. The thrust is the flat line: it comes from the mean stress rather than the difference, so it does not move at all. Putting 8 joints in this ring drops the moment to 34% of the solid one and leaves the thrust exactly where it was, which is why a segmental lining is jointed and why the intuition carried over from a beam is inverted here. Structural form

The lining that is stronger for being weaker

A tunnel lining is not loaded. The ground arrives already stressed and the hole wants to squash into an ellipse; the lining's only job is to refuse, and how much moment it collects depends entirely on how hard it refuses. Make it stiffer and it takes more. Make it flexible — put joints in it, make it thin — and it takes almost none, while the hoop thrust it carries does not move at all.

 Two identical pipes, and one carries three times the other. Load per metre on a buried conduit against the depth of cover, in trench widths, with the weight of the prism of soil directly above it drawn between them. A conduit laid in a narrow trench is stiffer than nothing and softer than the sides: the backfill settles relative to the undisturbed ground, the friction on the trench walls acts upward, and the conduit gets 64% of the prism. Lay the same conduit on the ground and build an embankment over it and it is now stiffer than the fill beside it, the interior prism settles less, the friction acts downward, and it gets 172% — a factor of 2.71 between two pipes with nothing different but which way the ground moved. The equation is Janssen's, the same one a silo wall obeys, with a trench for a silo; both curves start on the prism line, because with no depth there is no shear to redistribute anything. This is why a flexible pipe is buried rather than a rigid one: making the conduit weaker moves it down the page. Equilibrium

The pipe decides what the soil weighs

A buried conduit is not loaded by the soil above it. It is loaded by whatever share of that soil the relative movement leaves it — and which way the shear on the sides of the prism acts depends on whether the conduit settles more or less than the ground beside it. Two identical pipes under identical fill, one carrying two thirds of the prism and one carrying nearly twice it.

 The circle is searched for, and the first guess is 39 per cent optimistic. The same slope with 81 trial circles evaluated, each one through the toe and each one giving its own factor of safety. There is no equation whose solution is the answer: the slip surface is a shape the ground chooses, so the calculation is a search over shapes and the answer is the smallest number found — 1.191 against 1.650 for the circle a first guess puts through the toe from above the middle of the slope, which is 39 per cent optimistic. A slope analysis that reports one circle has reported nothing. Equilibrium

The surface that has to be searched for

Every other check in this collection is made at a section somebody drew. A slope has no section — the failure surface is a shape the ground chooses, so the calculation is a search over shapes, and the answer is the smallest number found rather than the solution of anything.

 Every pressure points at the pin, so the water lifts nothing. A radial gate of radius 8 m holding 6 m of water, with its pivot 6 m above the sill. The pressure on a curved surface cannot be obtained by multiplying anything by anything, so it is integrated round the arc: the horizontal component comes to 176.6 kN/m and the vertical to 110.5. Both are recoverable without any integral at all — the horizontal is the pressure force on the surface's own vertical projection, γH²/2 = 176.6, and the vertical is the weight of the water standing above it, 110.5. They agree to 0.000 per cent. And because every pressure is normal to a circle, every one of them passes through the centre: the moment of the whole 208 kN/m about the pivot is -3.4e-15 kNm, against 353 for a flat gate on the same hinge. Equilibrium

Every pressure points at the pin

Pressure acts normal to a surface, so on a curved one every element pushes in a different direction and no multiplication gives the resultant. Two free bodies recover it without an integral — and on a circular surface a third observation makes the whole force disappear from the equation a hoist has to satisfy.

 A pile has no length until the ground gives it one. Deflection, bending moment and soil reaction down a 0.6 m pile carrying 150 kN at a free head, in ground whose modulus grows by 0.005 N/mm³ per millimetre of depth. The one length in the problem is T, the fifth root of EI over n_h, which is 1.89 m here; the head moves 20.5 mm, the worst moment of 219 kNm is at 2.50 m — 1.32 T — and below about four T nothing happens at all. The classical coefficients come out of the finite differences rather than a table: 2.430 against Matlock and Reese's 2.435, and 0.772 against their 0.772. Internal forces

A pile has no length until the ground gives it one

Almost every other structural member is handed a length by the drawing. A pile goes into the ground until it stops, and what decides how much of it is working is a fifth root of the ratio between its own stiffness and the soil's.

 The summer that is worse than the one before it. The earth pressure behind an integral abutment, summer by summer, as a multiple of the at-rest value it started at. A 60 m deck expands by 10.8 mm at each end and pushes the abutment into the backfill. Granular soil under cyclic strain densifies, so the same movement next year needs a higher pressure to achieve, and K climbs from 0.38 toward 0.96 — a factor of 2.49 on the force, reached after about a century. The design load on an integral abutment describes the bridge's whole life rather than a load case, and it is the only load in this collection that gets larger because time has passed rather than because something was added. Structural form

The summer that is worse than the last

An expansion joint is a hole in a deck that leaks salt water onto the bearings underneath it. Remove it and the thermal movement does not go away — it goes into the soil behind the abutment, twice a day for a hundred and twenty years, and granular soil under cyclic strain gets denser.

 The roller's pressure, not the soil's. Horizontal pressure down the back of a wall, for backfill of 20 kN/m³ and φ′ = 30° behind a wall 3.0 m high, compacted by a roller of 60 kN per metre of its width. Dashed, the soil's own active pressure, Kₐ·γz (Kₐ = 0.33), and at-rest pressure, K₀·γz (K₀ = 0.50). Solid, Ingold's compaction envelope: rising as the passive limit γz/Kₐ to 27.6 kPa at 0.46 m, then constant at √(2pγ/π) = 27.6 kPa all the way down, since the active pressure would not reach it until 4.15 m. Its thrust is 76.6 kN per metre of wall against the active 30.0, and its moment about the base 106.3 kN·m against 30.0. Equilibrium

The pressure the roller leaves behind

A retaining wall is designed for the pressure of the soil it holds, a triangle growing with depth. The soil behind most walls was not tipped there. It was placed in layers and rolled, and each pass of the roller pushed the soil sideways against the wall harder than the soil's own weight ever could, and left most of that push locked in when it moved on. Behind a 3 m wall compacted by an ordinary vibrating roller the locked-in pressure is a constant 28 kPa from half a metre down, the thrust two and a half times the active triangle's and the moment at the base three and a half.

The library, page 2 of 7 — where earth-pressure sits