Structural Engineering & Statics
where the load goes
Generator

Three minima, and only two of them get a check

Rendered here at the parameters it defaults to, with every essay that calls it — which is the same list as the blast radius of changing it.
Three minima, and only two of them get a check. Elastic buckling stress against half-wavelength for a 200 × 65 × 15 × 1.5 mm lipped channel in uniform compression. The local minimum is at 200 mm and 41 N/mm²; the distortional at 689 mm and 287; the global curve falls away to the right and reaches 489 at the 1.5 m member. The distortional branch is a strut on an elastic foundation — the flange and lip rotating about the web junction, restrained by the web's own bending at 627 N·mm per radian per millimetre — so its minimum is at π(EC_w/k_φ)^¼ and its value is (2√(EC_wk_φ) + GJ)/I₀, the same closed form a continuously braced strut has. The elastic stresses are in the order local, distortional, global, and the mode that governs the strength is not the lowest of them, because they have very different amounts of post-buckling reserve.

Three minima, and only two of them get a check. Elastic buckling stress against half-wavelength for a 200 × 65 × 15 × 1.5 mm lipped channel in uniform compression. The local minimum is at 200 mm and 41 N/mm²; the distortional at 689 mm and 287; the global curve falls away to the right and reaches 489 at the 1.5 m member. The distortional branch is a strut on an elastic foundation — the flange and lip rotating about the web junction, restrained by the web's own bending at 627 N·mm per radian per millimetre — so its minimum is at π(EC_w/k_φ)^¼ and its value is (2√(EC_wk_φ) + GJ)/I₀, the same closed form a continuously braced strut has. The elastic stresses are in the order local, distortional, global, and the mode that governs the strength is not the lowest of them, because they have very different amounts of post-buckling reserve.

2 essays call signature-curve. The drawing above is what it returns with no arguments at all; every call below passes it something, because a placement that passes nothing draws whichever member of the family the generator happens to default to rather than the one its essay argues about.

Where it is called

Changing this generator changes every one of these figures.

Three minima, and only two of them get a check. Elastic buckling stress against half-wavelength for a 200 × 65 × 15 × 1.5 mm lipped channel in uniform compression. The local minimum is at 200 mm and 41 N/mm²; the distortional at 689 mm and 287; the global curve falls away to the right and reaches 489 at the 1.5 m member. The distortional branch is a strut on an elastic foundation — the flange and lip rotating about the web junction, restrained by the web's own bending at 627 N·mm per radian per millimetre — so its minimum is at π(EC_w/k_φ)^¼ and its value is (2√(EC_wk_φ) + GJ)/I₀, the same closed form a continuously braced strut has. The elastic stresses are in the order local, distortional, global, and the mode that governs the strength is not the lowest of them, because they have very different amounts of post-buckling reserve. Stability

The mode between the two that get checked

A thin-walled strut has three ways of buckling and two of them have design rules. The third has a half-wavelength several times the section depth, a shape in which the fold lines themselves move, and an elastic stress that no effective-width calculation can produce.

 A stiffener is a boundary condition, and it is bought at a threshold. The buckling stress of a 2400 × 12 mm plate with one longitudinal stiffener, against how rigid that stiffener is. Below γ the stiffener rides on the buckle and the plate takes the whole-width mode; at γ the stiffener stays straight and the plate buckles between stiffeners at 74 N/mm², 4.0 times the bare plate's 18.5. Above γ nothing further happens at all, because the sub-panel mode does not know the stiffener is there. The curve is a ramp and then a horizontal line, so a stiffener at twice γ is exactly as good as one at γ. Here γ = 31.5, which asks for an outstand of 144 mm; the 150 mm one drawn gives γ = 35.5, a margin of 1.13. Stability

The rib that is a boundary condition

A rib on a plate is not a member carrying load. It is a line the buckle is not allowed to cross — and it becomes one at a threshold. Below the required rigidity it rides on the buckle and buys a fraction; at the threshold it stays straight and the plate buckles between stiffeners; above it, nothing further happens at all.

The library, page 5 of 7 — where signature-curve sits