Generator

A column that was never straight

Rendered here at the parameters it defaults to, with every essay that calls it — which is the same list as the blast radius of changing it.

A column that was never straight. Load against lateral deflection at mid-height, for a column starting with an initial bow of 0.002. There is no critical value to reach: the deflection grows from the first increment, slowly at first and then without bound as the ratio approaches 1.00 — which is the Euler load, and which the column therefore never attains. The perfect column, drawn for comparison, sits on the vertical axis until it arrives there and then has no answer at all.

8 essays call imperfection-curve. The drawing above is what it returns with no arguments at all; every call below passes it something, because a placement that passes nothing draws whichever member of the family the generator happens to default to rather than the one its essay argues about.

Where it is called

Changing this generator changes every one of these figures.

Stability

The column that was never straight

Euler's load is the load at which a perfectly straight column becomes indifferent to being bent. No column is perfectly straight, so no column ever reaches it — and the load it never reaches can still be measured.

Deflection

The water that will not run off

A flat roof deflects, the deflection makes room for water, the water deepens the deflection. It is the same equation as a buckling column, with rain in place of the axial load.

Three paths out of the same critical load. Load against sideways movement past the critical load, for three systems whose critical loads are identical. The stable one climbs, so a real structure with a small crookedness reaches nearly the full load and keeps going. The unstable one falls symmetrically, so the imperfect structure has a maximum below the critical load and it matters not at all which way it leans. The asymmetric one falls one way and climbs the other, so the direction of the imperfection decides everything. All three are drawn at an imperfection of 0.02 radians.

Stability

A third of what the theory promised

A column with a small crookedness reaches almost its full Euler load. A cylinder with the same relative crookedness reaches a third of its classical one, and the theory is not wrong — what separates them is the slope of the path just past the critical load, which no calculation of the critical load itself can see.

Four camber rules, and what each leaves on the finished beam. The same 12 m composite beam, cambered against four different things, followed through its own load history. Positive is a sag and negative a hog, and the point at the left of each line is the shape it was fabricated to. Cambering against the wet concrete leaves 12.7 mm of sag at the end and a flat beam on the day the slab is poured; cambering against the total load leaves the beam dead flat when fully loaded and hogged 37.9 mm — one part in 316 of the span — before anything is on it at all.

Deflection

Built to the wrong shape on purpose

A cambered beam is fabricated curved upward so that load bends it down to something like straight. Nothing in the analysis changes, no stress anywhere is altered, and almost every mistake made with it is a bookkeeping mistake about which loads count.

The cheapest way out of being round. A ring under uniform external pressure, drawn in its first four buckling modes with the pressure each one needs underneath it, in N/mm². The pressure has no direction: it stays normal to the wall wherever the wall goes, so it does work on any change of shape that reduces the enclosed area, and the ring buckles into whichever shape is cheapest. Bare, that is the oval — n = 2 at 3EI/R³ — and the modes rise as n² − 1, so three lobes cost 2.67 times as much. Nothing in the drawing prefers any orientation, which is the point — a column has an axis to buckle about and a ring has none.

Stability

The pressure that needs no direction

Every buckling problem in this collection has had a load with a direction — a column pushed along its axis, a plate along its edge, an arch by what is on it. A buried pipe has none. The pressure is the same everywhere, it stays normal to the wall as the wall moves, and it does work on any change of shape that reduces the area inside.

A fourth power, and then a cliff. The factor of safety against rolling, against beam length, for one section hung from a roll axis 0.9 m above its centre of gravity. Nothing about the section changes along this axis. z̄ goes as the fourth power of the length — 0.236 m at 30 m becomes 0.747 m at 40 — and the factor of safety is proportional to (y_r − z̄), so it does not decline gently: it falls away and then stops existing. The working factor of 1.5 is lost at about 41 m, and past 42 m there is no hook height at all at which this beam hangs stably. Which is why long girders are lifted with the picks moved inboard, or with the beam braced, or not in one piece.

Stability

Hung from above and still unstable

A rigid body hanging from a point above its centre of gravity is a pendulum and cannot fall over. A beam is not rigid, and tilting it puts a component of its own weight sideways — which bows it, which moves its centre of gravity further out. Past a length there is no hook height at which it hangs stably at all, and the length arrives as a fourth power.

A weld is a force, and it is applied where the weld is. The bow a welded girder leaves the shop with, against how far its welds sit from the section's centroid. A weld cannot contract while the plate holds it, so it yields in tension and what is left when everything is cold is a locked-in force at about the yield stress: 312 kN for the 1.2 kJ/mm of heat drawn, over a shrinkage zone of 439 mm². Applied 210 mm off the centroid that is a moment, and a moment applied along a member is a curvature: the 12 m girder comes out bowed 12.5 mm, which is L/962 against a fabrication tolerance of L/1000. It also comes out 1.2 mm shorter. Welding symmetrically about the centroid puts the resultant on the neutral axis and the bow becomes 0.00 mm — the same heat, the same force, and no moment at all.

Connections

The shape that came out of the shop

A weld cools by seven hundred degrees while the plate holds it, so it yields in tension and stays that way. What is left is a locked-in force of three hundred kilonewtons applied where the weld is, and if that is not on the centroid the member leaves the shop bent.

The best design is where two failures arrive together. A fixed area of steel rolled into tubes of every proportion, with the three things that can end each one. Euler's load goes as r² because I = A r²/2; the local buckling stress goes as 1/r² because the wall thins as the tube grows; squashing does not care. The capacity is the lowest of the three, so it has a maximum — and the maximum is exactly where the two buckling curves cross, at r/t = 129 and 2364 kN, which the closed form r*, the fourth root of αAL² over π³β√3, reproduces to 0.52 per cent. That is the general result and it is not about tubes: the optimum of a minimum of a rising and a falling curve is always their intersection, so optimising a design against two failure modes puts both of them at the design point — which is the one configuration imperfections hurt most.

Stability

The best design is the most sensitive one

Take a fixed area of steel and roll it into a tube. Euler's load rises with the radius and local buckling falls with it, so the capacity has a maximum — and the maximum is exactly where the two failure modes arrive together, which is the one configuration imperfections hurt most.

The library, page 2 of 7 — where imperfection-curve sits