Structural Engineering & Statics
where the load goes
Concept

Method of joints — where it appears

Solving a truss by writing the two equilibrium equations at each joint in turn, taking joints in an order that never has more than two unknowns. It gives every member force and is slower than a section cut when only one of them is wanted.

Named by 6 essays across 3 fields — each of them below, with the objects they name alongside it.

A Pratt truss of 6 panels. A Pratt truss under equal panel-point loads. The joint equilibrium equations were assembled and solved; 10 members came out in tension, 9 in compression and 2 carrying nothing.

The triangle that cannot fold, and everything built out of it

A square of pinned bars is a mechanism. A triangle is not, and that single fact is the reason trusses exist and the reason they look the way they do.

structures · Truss The joints are not pins, and this is what that costs. A 4-panel Pratt truss solved twice on the same stiffness matrix: once with a moment release at every member end, which is the pin-jointed idealisation, and once with the joints continuous, which is what welding them produces. The axial forces are the same to within a per cent; the bending the second solution adds is worst in member 0, where the bending stress reaches 24.3% of the axial stress. Members are shaded by that ratio.

The joint that is not a pin

Every truss on this site is analysed as though its joints were frictionless pins. Almost none are. The bending that follows is called secondary, which is a claim about size — and the claim is checkable.

structures · Truss Every member's share of the movement, and they are not the members expected. A Pratt truss of six panels at a depth of 0.85, carrying 10 kN at each top node, with the movement of the bottom chord at mid-span attributed member by member. The unit-load sum δ = ΣF·f·L/EA gives 631.06 at EA = 1: 47.2% from four top chords, 28.5% from six bottom chords, 22.3% from six diagonals, 2.0% from five verticals. The single worst member is a top chord at mid-span at 14.8% of the whole. Each member is drawn at the width of its own share. The same deflection from a stiffness solution that shares none of this arithmetic is 631.06, a relative residual of 3.6e-15.

Which member moved the roof

A beam sags because it curves. A truss has no curvature anywhere — it comes down because every one of its members changes length, and the sum of those changes, weighted member by member, is a ranking that names which ones are worth stiffening. Usually not the ones a designer worries about.

deflection · Truss deflection A closed force polygon. The forces on a joint, laid tip to tail. Equilibrium is the statement that the polygon closes, and the gap when it does not is the out-of-balance force, to scale.

One drawing solves the whole truss

The method of joints solves a truss one joint at a time, and each solution is thrown away as soon as the next begins. Drawn instead of computed, the joints share their edges — every member's force appears once in a single figure, and the figure's own closure is the check.

structures · Truss A roof truss and its reciprocal figure. Left, a pitched roof truss of 8 m under three loads of 10.0 kN, its 13 members drawn in the colour of their force — 5 in tension, 6 in compression and 2 carrying nothing — with a letter on every region outside it between one external force and the next and a number on every cell inside it. Right, the force diagram: every lettered or numbered space is a point, every member is the line between the two spaces it separates, drawn parallel to the member and as long as its force, and every joint of the frame is a closed polygon. The eight joints and eleven spaces of the frame have become eight polygons and eight distinct points — fewer points than spaces, because some spaces land on one point, as the two either side of a member carrying nothing always do. Force times length adds to 190.0 kN·m over the tension members and 250.0 over the compression members, and the difference, −60.0, is fixed by the loads and where they act, whatever frame carries them. Each point was placed by crossing one member, and the 8 crossings not used to place anything all close to within 5e-15 kN.

Every space a point, every joint a polygon

A truss's force diagram is a second drawing of the truss in which the joints have become polygons and the spaces between members have become points. Maxwell showed in 1864 that the exchange runs both ways, so a designer can draw the forces first and ask what shape carries them. His theorem also says which frames have such a diagram at all, and the answer is a surprise, because it is about polyhedra.

equilibrium · Graphic statics Two pencil lines, and where they cross. Two lines drawn with a pencil 0.2 mm wide are two bands, drawn here much wider than a pencil so the shape can be seen, and they cross not at a point but in a parallelogram. At 60° apart the parallelogram's long diagonal is 2.0 pencil widths — 0.40 mm; at 12° apart the parallelogram's long diagonal is 9.6 pencil widths — 1.91 mm. The crossing's uncertainty along the bisector is the width divided by twice the sine of half the angle, so it grows without limit as the lines turn parallel, and a construction that finds a point by crossing two lines inherits it.

How wrong a drawing is

A pencil line is a band, and two bands cross in a parallelogram that grows as they turn parallel. The accuracy of a graphical construction is therefore a property of the angles it makes, not of the hand that made it — and the worst case is the shallow arch, the structure the method was most used on. Measured properly, the drawing's error there is the size of the builder's, and the check draughtsmen relied on cannot see it.

equilibrium · Graphic statics

Named alongside it

The objects these essays reach for when they reach for this one.

Force polygonGraphic staticsTrussZero-force memberDeterminacyFunicularReciprocal figureStiffnessTriangulationArchChord forceCompression

All concepts