Structural Engineering & Statics
where the load goes
Concept

Horizontal thrust — where it appears

The outward push an arch or a cable delivers at its supports, which is how the shape carries load and what the abutment must hold. It is inversely proportional to the rise, so a flat arch is an expensive abutment and a deep one is an expensive arch.

Named by 9 essays across 2 fields — each of them below, with the objects they name alongside it.

The cable and the arch are the same curve. The shape a cable takes under a uniform load is a parabola, and it carries that load in pure tension. Reflected, the identical curve carries the same load in pure compression, which is what an arch is.

The shape that carries itself, and the arch that is its reflection

Hang a chain and it takes the one shape that carries its load in pure tension. Turn the shape upside down and it carries the same load in pure compression. That is what an arch is.

structures · Funicular The funicular polygon for five loads. The shape a string takes under 5 point loads, with a vertex at every load and a constant horizontal component of 27.9 throughout. The end segments carry the most — 38.6 against 28.0 in the flattest one — because they are steepest.

The polygon that finds the shape

A hanging string under five loads has no smooth curve in it — it has five vertices and six straight segments, and every slope in it is a running sum divided by one number.

structures · Funicular A three-pinned arch, rise 2.6 on span 9. A three-pinned arch under a uniform load. One moment equation about the crown hinge gives a horizontal thrust of 23.37, with no stiffness and no assumption about the section. The thrust line lands on the axis everywhere, so there is no bending anywhere in the arch.

The hinge put in on purpose

An arch with two pinned feet cannot be solved by statics. Add a third hinge at the crown — deliberately weakening it — and the whole structure falls out of one moment equation.

structures · Arch A line of thrust, and the masonry it has to stay inside. An arch ring of 9% of the span in thickness, rising 28% of the span, under its own weight as a uniform load. Any horizontal thrust between 3.85 and 5.23 puts a line of compression entirely inside the masonry, so the arch stands — and which of them it actually takes is not decided by statics. The two extremes are drawn: the minimum-thrust line, which rides high at the crown and low at the haunches, and the maximum-thrust line, which does the opposite.

The line that must stay inside

A masonry arch does not stand because its shape is right. It stands because some line of compression can be drawn inside the stonework — any one will do, and there are infinitely many to choose from.

structures · Arch The further it deflects, the harder it pulls back. Total load against midspan sag for a 30 m cable of 1000 mm² prestressed to 500 kN, carrying 5 kN/m. The cubic H³ − T₀H² − w²L²EA/24 = 0 was bisected at every point of the curve, so the sag at the full 150 kN is 0.740 m rather than the 1.125 m the flat-cable formula WL/8T₀ gives — the straight dashed line, which is the tangent to this curve at the origin and nothing more. Its slope is the initial stiffness 8T₀/L = 133.3 kN/m; at the marked point the tangent has reached 341.2 kN/m, 2.56 times as stiff, and the horizontal component of the tension has risen from 500 kN to 760 kN. Nothing about the steel changed. The geometry got better at the job.

The stiffness that comes from the shape

A cable has no bending stiffness whatever, and it still holds up a roof. What resists the load is the change of its own geometry, so its stiffness is a function of the tension already in it — and prestress buys stiffness that no change of material could.

structures · Cable stiffness The hoops change their mind at an angle no proportion chose. The two membrane forces of a spherical dome of radius 30 m under 3 kN/m² of surface, taken from the crown to a base at 60°. The free body for the meridional force is the cap above a cone of half-angle φ, and vertical equilibrium of it gives N_φ = −wR/(1 + cos φ) directly: -45.0 kN/m at the crown falling to -60.0 at the base, compression everywhere. Equilibrium normal to the surface then gives the hoop force, which starts at -45.0 kN/m and reaches 15.0 — it changes sign, and the angle at which it does was found here by bisecting N_θ rather than quoted: 51.827292°. Setting N_θ = 0 gives cos²φ + cos φ − 1 = 0, so cos φ is (√5 − 1)/2, the reciprocal of the golden ratio — an identity this site's solver gate checks against the bisection to nine decimals rather than asserting, because it is too pretty to be believed on sight. Below that parallel the hoops are in tension, which masonry has none of, and that is where every old dome is cracked.

The surface that carries by being curved

A flat plate spends its thickness on a lever arm of a few millimetres. Curve the same sheet and the load is carried in the surface itself, at a thirtieth of the thickness — and the entire bill is presented at the edges.

structures · Shell action The same restraint, twice, with opposite signs. A 4 m strip of 200 mm slab whose ends cannot move apart, against deflection measured in its own thicknesses. The flat line is what a yield-line calculation gives, which is what the same strip would carry if its ends were free: 30.0 per unit width. The rising branch is compressive membrane action — the deflected strip is forced into an arch — and it peaks at 116.6, which is 3.89 times the yield-line load, at a deflection of 0.24 of the thickness. Past that the arch runs out of depth and the load falls back to the flexural one; past a deflection of one thickness there is no arch left and the reinforcement starts carrying the strip as a cable. It gets back to the arch's load at 2.17 thicknesses, which is one part in 9 of the span — a sag nobody would design for and exactly what a floor does instead of falling.

The force nobody put in the model

A slab strip whose ends cannot move apart is not the strip in the yield-line calculation. Deflecting shortens the chord between its ends, the ends do not come in, and the strip is forced into an arch — worth four times the load it was designed for, at a movement nobody would see.

internal-forces · Membrane action A cable alone goes to a kink, and a kink is not a road. A point load of 1000 at mid-span of a 900 m suspended deck. The upper shape is the cable with no girder at all: two straight lines meeting under the load, because a cable takes the funicular shape of whatever is on it and the funicular of a point load is a kink — 0.0083 radians of it here. The lower shape is the same cable with the girder present, peaking at 1.125 against the bare cable's 1.873. The girder is not carrying the load — it takes only 17% of it — it is spreading it, over a characteristic length of √(EI/H) = 183 m, and what reaches the cable is spread over that length rather than arriving at a point.

The deck is not there to carry the load

A cable takes the shape of whatever is on it, which is exactly the problem — under a point load its shape is a kink, and a kink is not a road. The stiffening girder exists to spread the load until what reaches the cable is something the cable's own shape is right for.

structures · Stiffening girder Three ways to move the same column, and they are not close. The same 2000 kN moved 3 m across 14 m, built three ways and drawn to one scale. The deep beam is 1.14 m of concrete, 24.1 tonnes, and settles 60.6 mm in the long term. The storey-deep truss takes the same moment as a couple at 3.6 m centres, so its chords carry M/h and it weighs 2.6 tonnes — a fifth of the beam — while settling 15.8 mm, and it does not creep. The wall is 72.8 tonnes and hardly moves at all, 1.71 mm, of which 36% is shear rather than bending — which is what a member as deep as it is long always does, and is why beam theory does not describe one. A wall as a deep beam is the stiffest of the three by a factor of 35.4.

The same span, four ways

A beam, a truss, an arch and a cable can all cross the same gap under the same load, and the choice between them is usually described as a matter of judgement or of taste. It is neither. Each carries the load by a different mechanism, each mechanism has a different exponent, and an exponent decides the ordering at every span rather than at some spans.

structures · Form selection

Named alongside it

The objects these essays reach for when they reach for this one.

FunicularSag ratioThrust lineCatenaryCompatibilityForm-findingMembrane actionSelf-weightStiffnessThree-pinned archAlternative load pathArch

All concepts