Structural Engineering & Statics
where the load goes
Series

Plate buckling — the series

4 essays on one idea, from the one that introduces it to the one that assumes the rest.
  1. A 8 mm plate, and the width it can be. The elastic critical stress of a plate in compression against its width, with the yield stress drawn across it. Below 370 mm the plate reaches yield before it buckles; above it the plate ripples first, and the fraction of the width still carrying load falls away — at 700 mm only 47 per cent of it is still working.

    The plate that ripples, and the width that is left

    A wide thin plate in compression buckles at a stress that has nothing to do with the strength of the material. It then goes on carrying load — the middle drops out, and the edges work harder.

    part 1 · stability
  2. A 10 mm plate, and the width it can be. The elastic critical stress of a plate in compression against its width, with the yield stress drawn across it. Below 462 mm the plate reaches yield before it buckles; above it the plate ripples first, and the fraction of the width still carrying load falls away — at 900 mm only 46 per cent of it is still working.

    The coefficient that is not four

    A plate's buckling stress carries a coefficient that looks like a constant and is not. It is 4 for an internal element, 0.43 for an outstand and 23.9 for a panel in shear — and the width a 10 mm plate may be runs from 152 mm to 1,130 across that range.

    part 2 · stability
  3. The coefficient is an envelope, and its scallops are whole half-waves. The plate buckling coefficient against aspect ratio α = a/b. Each faint branch is one half-wave count m: k = (m/α + α/m)², a curve whose own minimum is exactly 4 at α = m. The plate takes whichever branch is lowest, so the answer is the bold envelope — four touching 4 at α = 1, 2, 3 and 4, with cusps between them at α = √(m(m+1)) = 1.41, 2.45, 3.46, 4.47, where the plate is indifferent between m and m+1 half-waves. The first cusp reaches k = 4.50 and every later one is lower — 4.17, 4.08, 4.05. Past α = 1 the envelope never exceeds 4.49, which is why the length of a plate drops out of a formula that is otherwise entirely geometry.

    Four was never a fact about plates

    The coefficient every plate calculation starts from is quoted as 4, derived nowhere and remembered by everyone. It is the minimum of a quantity that has nothing to do with plates in it — and what the plate supplies is not the four but the restriction that produces the scallops around it.

    part 3 · stability
  4. The coefficient a web gets depends on where its neutral axis is. The plate buckling coefficient for an internal element against ψ = σ₂/σ₁, the ratio of the stresses at the two edges of the panel. Uniform compression is ψ = 1 and k = 4; a gradient running from compression to zero is ψ = 0 and k = 7.81; pure bending is ψ = −1 and k = 23.92, six times the value a column's flange gets. The 1800 × 12 mm web drawn here starts at ψ = −1.000 and k = 23.92 and ends at ψ = −0.910 and k = 21.63, because losing width from the compressed half drops the neutral axis and deepens the compression zone. The curve is steepest exactly where a bending web sits, so a small movement of the neutral axis costs 2.29 of coefficient.

    Classified by a gradient it does not have

    A web in bending is the one plate whose buckling coefficient cannot be looked up. It depends on the stress gradient, the gradient depends on where the neutral axis is, and the neutral axis depends on how much of the web the coefficient has just taken away — so the answer is a fixed point, and the calculation everyone does is its first term.

    part 4 · stability

All series