Structural Engineering & Statics
where the load goes
Generator

One criterion inside the other, touching at six points

Rendered here at the parameters it defaults to, with every essay that calls it — which is the same list as the blast radius of changing it.
One criterion inside the other, touching at six points. The two yield criteria in principal stress space with the third principal stress zero, both normalised by the yield stress. Von Mises is the ellipse — σ₁² − σ₁σ₂ + σ₂² = f_y², which is a circle seen at an angle — and Tresca is the hexagon inscribed in it, touching at the six points where one principal stress is zero or the two are equal. Everywhere else Tresca is the smaller, by up to 15.5 per cent, and the widest gap is at pure shear, where σ₁ = −σ₂ and the two answers are 205 and 178 N/mm². The ratio there is exactly 2/√3, computed rather than quoted, and it is the whole reason a web is checked against f_y over root three.

One criterion inside the other, touching at six points. The two yield criteria in principal stress space with the third principal stress zero, both normalised by the yield stress. Von Mises is the ellipse — σ₁² − σ₁σ₂ + σ₂² = f_y², which is a circle seen at an angle — and Tresca is the hexagon inscribed in it, touching at the six points where one principal stress is zero or the two are equal. Everywhere else Tresca is the smaller, by up to 15.5 per cent, and the widest gap is at pure shear, where σ₁ = −σ₂ and the two answers are 205 and 178 N/mm². The ratio there is exactly 2/√3, computed rather than quoted, and it is the whole reason a web is checked against f_y over root three.

3 essays call yield-surface. The drawing above is what it returns with no arguments at all; every call below passes it something, because a placement that passes nothing draws whichever member of the family the generator happens to default to rather than the one its essay argues about.

Where it is called

Changing this generator changes every one of these figures.

One criterion inside the other, touching at six points. The two yield criteria in principal stress space with the third principal stress zero, both normalised by the yield stress. Von Mises is the ellipse — σ₁² − σ₁σ₂ + σ₂² = f_y², which is a circle seen at an angle — and Tresca is the hexagon inscribed in it, touching at the six points where one principal stress is zero or the two are equal. Everywhere else Tresca is the smaller, by up to 15.5 per cent, and the widest gap is at pure shear, where σ₁ = −σ₂ and the two answers are 205 and 178 N/mm². The ratio there is exactly 2/√3, computed rather than quoted, and it is the whole reason a web is checked against f_y over root three. Materials

The shear strength nobody measured

Every steel web in a design check is checked against the yield stress divided by the square root of three, and no test produced that number. It is a consequence of a decision about what makes a metal yield, and the alternative decision gives a different answer by fifteen per cent.

 An enhanced strength that is the strength of a tie. Bearing strength as a multiple of the design cylinder strength, against how far the load is allowed to spread, with the bursting tension the spread creates on the same axis. The enhancement is √(A₂/A₁) and it reaches 2.80 for the 250 mm pad on a 700 mm block drawn — 47.6 N/mm² against a design strength of 17.0. There is no material property in that statement beyond the one being enhanced, and the reason is on the second curve: a load that spreads does so along inclined struts, a pair of inclined struts has a horizontal component, and that component is 16.1% of the load. It has to be tied. 1099 mm² of steel is what the enhancement actually is, and the cap of three is not a property of concrete — it is the angle past which nobody believes the strut. Internal forces

Three times as strong under a smaller pad

Press a small plate onto a large block of concrete and it will carry three times the stress a cylinder of the same concrete fails at. The enhancement is a ratio of areas with no material property in it, which should be a warning: what has actually been measured is not the concrete's strength but the strength of a tie holding it together.

 One point, every plane through it, one circle. A point carrying 180 N/mm² across one face, 90 across the other and 40 of shear. As the plane is turned, the pair (σ, τ) runs round a circle of radius 60.2 centred at 135.0 — and it goes round at twice the rate the plane does, which is the part always misremembered and the part that makes the picture work. The principal stresses are 195.2 and 74.8, on planes 20.8° from the face the 180 acts on; the largest shear on any plane is 60.2, exactly the radius, and it sits 45° from those — which is 90° round the circle. The von Mises stress that ranks this state against any other is 170.6. Sections and stress

The circle nobody draws

A plane stress state has three principal stresses and the third is zero. When the two on the drawing share a sign, the largest shear in the state involves the one that is not there — and the circle a designer has drawn is not the circle that governs.

The library, page 7 of 7 — where yield-surface sits