Generator

Take that one away and the load finds another route

Rendered here at the parameters it defaults to, with every essay that calls it — which is the same list as the blast radius of changing it.

Take that one away and the load finds another route. A 6-panel pratt truss under 20 kN at each top node, before and after member 2 is removed. The load redistributes. The worst-affected survivor now carries 2.03 times what it did, and four members that carried nothing before are now working. Whether that is survival depends on how much spare capacity was there, which is a different question from whether the frame was strong enough.

5 essays call member-loss. The drawing above is what it returns with no arguments at all; every call below passes it something, because a placement that passes nothing draws whichever member of the family the generator happens to default to rather than the one its essay argues about.

Where it is called

Changing this generator changes every one of these figures.

Structural form

The structure that survives losing a member

Every check in this collection asks what a structure carries. None of them asks what is left when part of it is gone — and two frames with the same members, the same weight and the same factor of safety can answer that question completely differently.

The same restraint, twice, with opposite signs. A 4 m strip of 200 mm slab whose ends cannot move apart, against deflection measured in its own thicknesses. The flat line is what a yield-line calculation gives, which is what the same strip would carry if its ends were free: 30.0 per unit width. The rising branch is compressive membrane action — the deflected strip is forced into an arch — and it peaks at 116.6, which is 3.89 times the yield-line load, at a deflection of 0.24 of the thickness. Past that the arch runs out of depth and the load falls back to the flexural one; past a deflection of one thickness there is no arch left and the reinforcement starts carrying the strip as a cable. It gets back to the arch's load at 2.17 thicknesses, which is one part in 9 of the span — a sag nobody would design for and exactly what a floor does instead of falling.

Internal forces

The force nobody put in the model

A slab strip whose ends cannot move apart is not the strip in the yield-line calculation. Deflecting shortens the chord between its ends, the ends do not come in, and the strip is forced into an arch — worth four times the load it was designed for, at a movement nobody would see.

The corner columns take what the middle ones did not. Axial stress in the columns across one flange face of a 36 by 36 m framed tube, at the base. Plane sections says the flat line: every column on the face at the same distance from the neutral axis, therefore at the same stress. The solved distribution is the curve — 78.5 N/mm² at the corner against 13.4 in the middle, a ratio of 5.88. The middle columns lag because the only route the axial force has into them is the in-plane shear of the spandrel frame, bay by bay from the corner. The face is carrying its resultant on an effective width of 45 per cent, and the tube deflects as though its second moment were 64 per cent of the gross.

Structural form

The columns that lean

A framed tube carries its wind load by bending the spandrel beams between its columns, and it does it badly — the corner columns take nearly six times what the middle ones do. Tilt the columns instead, so the perimeter is triangulated, and the same shear is carried axially. The concentration falls to 1.21 and the tube recovers most of the stiffness the plan said it had.

Removing each member in turn. Every member of a 8-panel pratt truss removed one at a time, with the worst demand on the survivors plotted against the member removed. Four of the 35 leave a mechanism — the bars drawn to the top of the frame — and for those there is no redistribution to compute, because there is no structure left. The rest redistribute, and the worst of them asks a survivor for 2.04 times what it carried before. A single number for robustness does not exist: it depends on which member goes.

Structural form

A determinate truss has no robustness at all

Remove any one of a Warren truss's thirty-one members and what is left is a mechanism. Not weakened — gone, with no set of forces that holds the load in any position. Robustness is not a property a structure has by degree; it is bought by adding members that carry nothing until something else stops carrying, and a truss without them has none of it to measure.

Three members after a diagonal goes. The forces in three members of the counter-braced truss when the diagonal 9–2, carrying 242 kN, is removed instantaneously, with 2 per cent damping, over one and a half of the damaged truss's first periods (0.57 s); dashed, the static force each settles to. The counter-diagonal 1–10 goes from −112 kN to −354 kN and peaks at −491 kN, 1.57 times its change. The bottom chord 3–4 ends exactly where it started, 750 kN, and on the way peaks at 1,115 kN. The bottom chord 2–3 settles lower, at 556 kN, after a first swing the other way, to 905 kN.

Structural form

The factor of two belongs to one mode

A member that fails suddenly hands its force to the structure around it all at once, and the convention is to double the static answer: a load applied suddenly to a spring overshoots to twice its static deflection. A truss is not one spring. Take a diagonal out of a counter-braced truss in an instant and some members swing to three times their change of force, one swings the wrong way first, and a bottom chord whose force does not change at all passes through half as much again as it carries — because every mode overshoots by two, at its own time, and a member is a sum of modes.

The library, page 3 of 7 — where member-loss sits